[PATCH v3] gdb: tests: set remotetimeout to gdb_load_timeout for remote targets

[Mike Frysinger <vapier at gentoo dot org>]

From: Jie Zhang <jie.zhang@analog.com>

Rather than relying on the default remotetimeout value (which might be
too small for some slower devices), use the existing gdb_load_timeout
config option to set it.

This adds two new helpers for getting/setting the remotetimout to keep
the new logic simple.

Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
v3
	- add comments to new helper funcs
	- use gdb_test_multiple

 gdb/testsuite/config/monitor.exp |   16 +++++++++++++++-
 gdb/testsuite/lib/gdb.exp        |   27 +++++++++++++++++++++++++++
 2 files changed, 42 insertions(+), 1 deletions(-)

diff --git a/gdb/testsuite/config/monitor.exp b/gdb/testsuite/config/monitor.exp
index be98f1a..ca11600 100644
--- a/gdb/testsuite/config/monitor.exp
+++ b/gdb/testsuite/config/monitor.exp
@@ -226,6 +226,12 @@ proc gdb_load { arg } {
 		set loadtimeout 1600
 	    }
 
+	    if [is_remote target] {
+		set oldremotetimeout [get_remotetimeout]
+		set_remotetimeout $loadtimeout
+	    }
+
+	    set load_ok 0
 	    send_gdb $command;
 	    gdb_expect $loadtimeout {
 		-re "\[Ff\]ailed.*$gdb_prompt $" {
@@ -235,7 +241,7 @@ proc gdb_load { arg } {
 		}
 		-re "$gdb_prompt $" {
 		    verbose "Loaded $farg into $GDB\n"
-		    return 0;
+		    set load_ok 1
 		}
 		timeout {
 		    if { $verbose > 1 } {
@@ -243,6 +249,14 @@ proc gdb_load { arg } {
 		    }
 		}
 	    }
+
+	    if [is_remote target] {
+		set_remotetimeout $oldremotetimeout
+	    }
+
+	    if { $load_ok == 1 } {
+		return 0;
+	    }
 	}
 
 	# Make sure we don't have an open connection to the target.
diff --git a/gdb/testsuite/lib/gdb.exp b/gdb/testsuite/lib/gdb.exp
index 091b271..de9b4ea 100644
--- a/gdb/testsuite/lib/gdb.exp
+++ b/gdb/testsuite/lib/gdb.exp
@@ -3626,6 +3626,33 @@ proc get_sizeof { type default } {
     return [get_integer_valueof "sizeof (${type})" $default]
 }
 
+# Get the current value for remotetimeout and return it.
+proc get_remotetimeout { } {
+    global gdb_prompt
+    global decimal
+
+    gdb_test_multiple "show remotetimeout" "" {
+	-re "Timeout limit to wait for target to respond is ($decimal).*$gdb_prompt $" {
+	    return $expect_out(1,string);
+	}
+    }
+
+    # Pick the default that gdb uses
+    warning "Unable to read remotetimeout"
+    return 300
+}
+
+# Set the remotetimeout to the specified timeout.  Nothing is returned.
+proc set_remotetimeout { timeout } {
+    global gdb_prompt
+
+    gdb_test_multiple "set remotetimeout $timeout" "" {
+	-re "$gdb_prompt $" {
+	    verbose "Set remotetimeout to $timeout\n"
+	}
+    }
+}
+
 # Log gdb command line and script if requested.
 if {[info exists TRANSCRIPT]} {
   rename send_gdb real_send_gdb
-- 
1.7.6