This is the mail archive of the
ecos-discuss@sourceware.org
mailing list for the eCos project.
Re: Fwd: AT91SAM7X-EK with TC/IP - unresolved conflicts
- From: Andrew Lunn <andrew at lunn dot ch>
- To: Robert Brusa <bob dot brusa at gmail dot com>
- Cc: ecos-discuss at ecos dot sourceware dot org
- Date: Mon, 1 Sep 2008 11:36:43 +0200
- Subject: Re: [ECOS] Fwd: AT91SAM7X-EK with TC/IP - unresolved conflicts
- References: <op.ugnlflqpkeg3uf@localhost> <op.ugnljtyskeg3uf@localhost> <48B8137D.7040803@mlbassoc.com> <20080829162608.GV31987@lunn.ch> <op.ugspx7q0keg3uf@localhost>
On Mon, Sep 01, 2008 at 11:28:58AM +0200, Robert Brusa wrote:
> On Fri, 29 Aug 2008 18:26:08 +0200, Andrew Lunn <andrew@lunn.ch> wrote:
>
> ...some old stuff removed...
>
>> However, this is a pointless exercise. The AT91SAM7X only has 64K
>> RAM. Getting the FreeBSD stack to work in that is probably impossible.
>>
>> Try the lwip_eth template. Then you will need to tune the lwip
>> configuration.
>>
>> Andrew
>
> Not beeing able to use ethernet would be a serious blow to my planing.
I never said that. I just said the FreeBSD stack will not work. The
lwip stack has been shown to work on the AT91SAM7X. Go google lwip.
> Is RPC supported by ecos?
RPC is too generic a word. Do you mean Suns RPC used by NFS, RFC 1057?
Do you mean XML-RPC like http://www.xmlrpc.com/. Do you mean COBRA?
Out of the box eCos supports none of these. However you could port
something or write your own RPC code.
> Back to the above exercise: When using ecosconfig, it seems to work, but
> when I call ecosconfig check, I get the following:
> ================ calling ecosconfig --verbose check
> ecos.db, package CYGPKG_HAL_FR30_MB91360: warning
> This package is not present in the component repository.
> There is no directory `/opt/ecos/ecos-2.x/packages/hal/fr30/mb91360'.
> ecos.db, package CYGPKG_HAL_FR30_MB91360_PHYTEC91F364G: warning
> This package is not present in the component repository.
> There is no directory
> `/opt/ecos/ecos-2.x/packages/hal/fr30/phytec91f364g'.
> ecos.db, target phytec91f364g: warning
> This target refers to an unknown package `CYGPKG_HAL_FR30_MB91360'.
> ecos.db, target phytec91f364g: warning
> This target refers to an unknown package
> `CYGPKG_HAL_FR30_MB91360_PHYTEC91F364G'.
> ecos.db, target pc_usb_d12: warning
> This target refers to a package `CYGPKG_IO_FILEIO' that is not
> hardware-specific.
> Target: at91sam7xek
> Template: net
> No conflicts
> =============
> Then I call make. It goes through with much output and no errors, but I
> can find nowhere a result (library). ????
Look in install/lib .
Andrew
--
Before posting, please read the FAQ: http://ecos.sourceware.org/fom/ecos
and search the list archive: http://ecos.sourceware.org/ml/ecos-discuss