This is the mail archive of the
mailing list for the eCos project.
Re: TCP Stack Testing problem
On Fri, Dec 30, 2005 at 11:51:19PM +0530, Madhava Reddy S wrote:
> Thanks a lot.
> I have tried to compile redboot code and tried to generate library but it
> was giving lot of errors and warnings.
> I want to ping to target system.
> To do that is it compulsory to go for redboot support.Is there any other
> way apart form redboot package selection.
As i said in my reply, normal TCP/IP will work without Redboot.
> Madhava S
> ----- Original Message -----
> From: "Andrew Lunn" <email@example.com>
> To: "Madhava Reddy S" <firstname.lastname@example.org>
> Cc: <email@example.com>
> Sent: Friday, December 30, 2005 8:37 PM
> Subject: Re: [ECOS] TCP Stack Testing problem
> >On Fri, Dec 30, 2005 at 07:36:02PM +0530, Madhava Reddy S wrote:
> >>Hi All,
> >>I am new to eCos and currently learning to work on x86 PC platform.
> >>I want to test the working of TCP/IP stack.
> >>I was able to compile and run a sample application using boot floppy
> >>through serial port.
> >>How can i test the same program using Ethernet port.
> >>In the configuration tool i have selected "common ethernet support",
> >>"networking" and "Open BSD Stack" packages.
> >Rather than add packages like this, use the templates, eg net and
> >>I have generated the library for my work_dir.
> >>Then i have compiled the program using
> >>i386-elf-gcc -g -I$(work_dir)/include/hello.c -L$(work_dir)/lib
> >>-nostdlib -o nw_test
> >>Generated the binary of that exe
> >>i386-elf-objcpy -O binary nw_test nw_test.bin
> >>copied to floppy
> >>dd conv=sync if=nw_test.bin of=/dev/fd0
> >>I compiled the target for booting from floppy.
> >>Started the target.
> >>On Host i started gdb
> >>i386-elf-gdb nw_test
> >>when i try to connect using "target remote ip:port"
> >>it says destination unreachable.
> >Only redboot contains a tcp/ip enabled stub which can be used by
> >gdb. Your FLOPPY startup application only has a serial port gdb stub.
> >This is not a problem though, normal TCP/IP will still work and you
> >just need to use the serial port for gdb.
> >Also, rather than writing your own test programs, i suggest you first
> >use the eCos test programs. These are known to work. Enable
> >CYGPKG_NET_BUILD_HW_TESTS and do a
> >make tests
> >and run the applications in install/tests/net/bsd_tcpip
> > Andrew
> >Before posting, please read the FAQ: http://ecos.sourceware.org/fom/ecos
> >and search the list archive: http://ecos.sourceware.org/ml/ecos-discuss
> This e-mail contains PRIVILEGED AND CONFIDENTIAL INFORMATION intended solely for the use of the addressee(s). If you are not the intended recipient, please notify the sender by e-mail and delete the original message.Global Edge Software Ltd has taken every reasonable precaution to minimize this risk, but is not liable for any damage you may sustain as a result of any virus in this e-mail. You should carry out your own virus checks before opening the e-mail or attachment. Global Edge Software Ltd reserves the right to monitor and review the content of all messages sent to or from this e-mail address
Before posting, please read the FAQ: http://ecos.sourceware.org/fom/ecos
and search the list archive: http://ecos.sourceware.org/ml/ecos-discuss