This is the mail archive of the
ecos-discuss@sources.redhat.com
mailing list for the eCos project.
Re: ethernet driver ioctl() call not getting initiated!
- From: Gary Thomas <gary at mlbassoc dot com>
- To: Raja Mallik <raja dot mallik at moschip dot com>
- Cc: eCos Discussion <ecos-discuss at ecos dot sourceware dot org>
- Date: Tue, 17 May 2005 08:01:16 -0600
- Subject: Re: [ECOS] ethernet driver ioctl() call not getting initiated!
- References: <1116337408.1685.60.camel@mazda>
On Tue, 2005-05-17 at 19:13 +0530, Raja Mallik wrote:
> Hi all!
>
> I have found that some how that application ethernet driver is not able
> to initiate ioctl() call..which is must for setting MAC, the IP, the
> Netmask, the broadcast address, etc..
>
> I am getting these errors!
>
> I am just unable to find why this is happening..is that I have have any
> trouble of using freeBSD network stacks..
>
You don't have an 'eth0' device (it seems to be called 'SCP_eth').
Unless you change some other configury, the default setup won't find
any ethernet device to use.
>
> Regards
> Raja
>
>
>
> Cosole print out
>
>
> ## Starting application at 0x00030000 ...
> Init device '/dev/ttydiag'
> Init tty channel: 68bcc
> Init device '/dev/tty0'
> Init tty channel: 68be8
> Init device '/dev/haldiag'
> HAL/diag SERIAL init
> [cyg_net_init] Init: mbinit(0x00000000)
> [cyg_net_init] Init: cyg_net_init_devs(0x00000000)
> Init device 'SCP_eth'
> Starting to initialise mcs1000 driver
> Name of interface is SCP_eth
> Device Instance name is eth0_scp
> Using port: EthA
> RX Buf shift state: 0x01
>
> Link: 10MB/s Full Duplex
> mcs1000 driver initialised eth_drv_init() and started
> [cyg_net_init] Init: loopattach(0x00000000)
> [cyg_net_init] Init: ifinit(0x00000000)
> IFP: 0x000680dc, next: 0x000afd60
> IFP: 0x000afd60, next: 0x00000000
> [cyg_net_init] Init: domaininit(0x00000000)
> [cyg_net_init] Init: cyg_net_add_domain(0x0006896c)
> New domain internet at 0x00000000
> [cyg_net_init] Init: cyg_net_add_domain(0x00068474)
> New domain route at 0x00000000
> [cyg_net_init] Init: cyg_route_init(0x00000000)
> [cyg_net_init] Done
> dn
> .
> .
> .
> up
> .
> .
> .
> init...
> -list vectors vector=24, handle=30b24, int=0 ,h0,iaf8a0
> -mac irq attached to vector 24
> -list vectors vector=4, handle=30b24, int=4 ,h0,iaf8a4
> -mac irq attached to vector 4
> -list vectors vector=6, handle=30b24, int=8 ,h0,iaf8a8
> -mac irq attached to vector 6
> -list vectors vector=19, handle=30b24, int=c ,h0,iaf8ac
> -mac irq attached to vector 19
> -list vectors vector=5, handle=30b24, int=10 ,h0,iaf8b0
> -mac irq attached to vector 5
> -list vectors vector=7, handle=30b24, int=14 ,h0,iaf8b4
> -mac irq attached to vector 7
> -list vectors vector=20, handle=30b24, int=18 ,h0,iaf8b8
> -mac irq attached to vector 20
> Link status for if0
> 100M
>
> 30 30 3a 66 66 3a
> IN MAC REG 663A30303A66
>
> Start PING test
> Error: SIOCGIFHWADDR 2: Device not configured
> Mac addr 03:00:f8:84:03:00
> started Socket PF_NET, SOCK_DGRAM
> will do memset
> finished doing memset
> finished doing stringcopy
> Cannot obtain MAC adress :Device not configuredCant set IP of 'eth0' to
> '192.168.1.143' Error :'Device not configured'
> Net Mask Error : Device not configured
> BroadCastError:Device not configured
> Error: SIOCGIFHWADDR 2: Device not configured
> Mac addr 08:40:9c:56:06:00
> Cant set IP of 'eth0' to '192.168.1.144' Error :'Device not configured'
> Net Mask Error : Device not configured
> BroadCastError:Device not configured...
>
>
>
--
------------------------------------------------------------
Gary Thomas | Consulting for the
MLB Associates | Embedded world
------------------------------------------------------------
--
Before posting, please read the FAQ: http://ecos.sourceware.org/fom/ecos
and search the list archive: http://ecos.sourceware.org/ml/ecos-discuss