[ECOS] ethernet driver ioctl() call not getting initiated!

[Raja Mallik <raja dot mallik at moschip dot com>]

Hi all! 
 
I have found that some how that application ethernet driver is not able
to initiate ioctl() call..which is must for setting MAC, the IP, the
Netmask, the broadcast address, etc..

I am getting these errors!

I am just unable to find why this is happening..is that I have have any
trouble of using freeBSD network stacks..


Regards
Raja



Cosole print out


## Starting application at 0x00030000 ...
Init device '/dev/ttydiag'
Init tty channel: 68bcc
Init device '/dev/tty0'
Init tty channel: 68be8
Init device '/dev/haldiag'
HAL/diag SERIAL init
[cyg_net_init] Init: mbinit(0x00000000)
[cyg_net_init] Init: cyg_net_init_devs(0x00000000)
Init device 'SCP_eth'
Starting to initialise mcs1000 driver
Name of interface is SCP_eth
Device Instance name is eth0_scp
Using port: EthA
RX Buf shift state: 0x01
                                                                                                                             
Link: 10MB/s Full Duplex
mcs1000 driver initialised eth_drv_init() and started
[cyg_net_init] Init: loopattach(0x00000000)
[cyg_net_init] Init: ifinit(0x00000000)
IFP: 0x000680dc, next: 0x000afd60
IFP: 0x000afd60, next: 0x00000000
[cyg_net_init] Init: domaininit(0x00000000)
[cyg_net_init] Init: cyg_net_add_domain(0x0006896c)
New domain internet at 0x00000000
[cyg_net_init] Init: cyg_net_add_domain(0x00068474)
New domain route at 0x00000000
[cyg_net_init] Init: cyg_route_init(0x00000000)
[cyg_net_init] Done
dn
.
.
.
up
.
.
.
init...
-list vectors vector=24, handle=30b24, int=0 ,h0,iaf8a0
-mac irq attached to vector 24
-list vectors vector=4, handle=30b24, int=4 ,h0,iaf8a4
-mac irq attached to vector 4
-list vectors vector=6, handle=30b24, int=8 ,h0,iaf8a8
-mac irq attached to vector 6
-list vectors vector=19, handle=30b24, int=c ,h0,iaf8ac
-mac irq attached to vector 19
-list vectors vector=5, handle=30b24, int=10 ,h0,iaf8b0
-mac irq attached to vector 5
-list vectors vector=7, handle=30b24, int=14 ,h0,iaf8b4
-mac irq attached to vector 7
-list vectors vector=20, handle=30b24, int=18 ,h0,iaf8b8
-mac irq attached to vector 20
Link status for if0
 100M
                                                                                                                             
 30 30 3a 66 66 3a
IN MAC REG 663A30303A66

Start PING test
Error: SIOCGIFHWADDR 2: Device not configured
Mac addr 03:00:f8:84:03:00
started Socket PF_NET, SOCK_DGRAM
will do memset
finished doing memset
finished doing stringcopy
Cannot obtain MAC adress :Device not configuredCant set IP of 'eth0' to
'192.168.1.143' Error :'Device not configured'
Net Mask Error : Device not configured
BroadCastError:Device not configured
Error: SIOCGIFHWADDR 2: Device not configured
Mac addr 08:40:9c:56:06:00
Cant set IP of 'eth0' to '192.168.1.144' Error :'Device not configured'
Net Mask Error : Device not configured
BroadCastError:Device not configured...




-- 
Before posting, please read the FAQ: http://ecos.sourceware.org/fom/ecos
and search the list archive: http://ecos.sourceware.org/ml/ecos-discuss