RE: [ECOS] issue about porting ecos on new target board

["Robert Cragie" <rcc at jennic dot com>]

I have found data sheet on S3C44B0X which is a similar part to the one you
mention and, yes, you're right, it's quite different.

In this case, you would still be wise to start from an ARM7TDMI core based
port, so 'e7t' or 'snds' would still be appropriate. However, you will need
to consider all aspects of the port - the cache control, UART, system
configuration, memory map, clock configuration etc. when doing the port. I
would suggest buying Anthony Massa's book 'Embedded Software Development
with eCos' (ISBN 0-13-035473-2) - this has a whole chapter on porting.

Robert Cragie, Design Engineer
_______________________________________________________________
Jennic Ltd, Furnival Street, Sheffield, S1 4QT,  UK
http://www.jennic.com  Tel: +44 (0) 114 281 2655
_______________________________________________________________

> -----Original Message-----
> From: P_CHING_KUANG [mailto:p_ching_kuang at ms10 dot url dot com dot tw]
> Sent: 16 April 2003 11:59
> To: rcc at jennic dot com
> Subject: [ECOS] issue about porting ecos on new target board
>
>
> Dear,
> Thanks for replying.
> I think it is not similar with the S3C4510/S3C4530.
>
> You can find this process at below website:
> http://www.samsungusa.com/cgi-
> bin/nabc/semiconductors/system_lsi/32_bit_arm_based_risc_mpu/pda/k
> s32c41000/
> ks32c41000.jsp
>
> Hope to hear your reply, thanks.
>
> Regards,
> Steve
>
> ____________________Original Message_____________________
>
> I can't find any information about your processor on the Samsung website
> (http://www.samsung.com/Products/Semiconductor/). However, it
> sounds like it
> might be similar to the S3C4510/S3C4530 used in ARM's E7T or Samsung's
> SNDS100, so the 'e7t' or 'snds' targets would probably be your
> best starting
> point for a port.
>
> Robert Cragie, Design Engineer
> _______________________________________________________________
> Jennic Ltd, Furnival Street, Sheffield, S1 4QT,  UK
> http://www.jennic.com  Tel: +44 (0) 114 281 2655
> _______________________________________________________________
>
> > -----Original Message-----
> > From: ecos-discuss-owner at sources dot redhat dot com
> > [mailto:ecos-discuss-owner at sources dot redhat dot com]On Behalf Of P_CHING_KUANG
> > Sent: 16 April 2003 04:45
> > To: ecos-discuss at sources dot redhat dot com
> > Subject: [ECOS] issue about porting ecos on new target board
> >
> >
> > Dear,
> >
> > I am new for ecos project, and I want to port it on Samsung KS32C41000
> > ARM7TDMI CPU.
> > Do you have some suggestion?  Which process supported by ecos is similar
> > with this process ?
> >
> > Regards,
> > Steve
> >
> >
> > ------------------------------------------
> > 台灣最物超所值的大眾化虛擬郵件主機
> > http://mymailer.url.com.tw
> >
> >
> >
> > --
> > Before posting, please read the FAQ: http://sources.redhat.com/fom/ecos
> > and search the list archive: http://sources.redhat.com/ml/ecos-discuss
> >
> >
>
>
> ------------------------------------------
> 台灣最物超所值的大眾化虛擬郵件主機
> http://mymailer.url.com.tw
>
>
>


-- 
Before posting, please read the FAQ: http://sources.redhat.com/fom/ecos
and search the list archive: http://sources.redhat.com/ml/ecos-discuss